has both GSM and MA . Here I'll discuss on how to Flash/Software Update/Debrand GSM . Flashing depends on Platform rather than Model, so you may notice one model uses one flasher but the next model uses another. Different models which are from same platform use same flasher. has several platforms like Infineon, Qualcomm, ADI, TI, MTK, SEMC etc. I'll try describe on ch platform how to flash a phone. Remember that, till now XP is the best performing Operating Syetem for flashing.
~INFINEON~
based on Infineon platform are flashed with GSMulti software. GSMulti has different versions like 20, 21, 30. The last one is GSMulti V30 and it supports all infineon till now. Infineon can be flashed both in USB and UART mode. Normally USB should be used, it will flash the phone in minutes where UART will take hour(s). Sometimes when phone is dd or rebooting and can't install USB driver you need to use UART then. Some old support only UART.
Infineon flashing on UART 1. You need a USB to Converter BOX/Cable with correct pinout of the phone. 2. Install and run GSMulti v30 3. Go to Setting(s) > Configuration, select DLL and firmware on S/W box, select UART as communiion, select correct port of Box/cable, then click OK. 4. Now click START on main window, when the software says Wait Phone Connecting... connect POWERED OFF phone with battery to cable and press POWER button.
Infineon flashing on USB 1. Install GSMULti V30 2. Connect phone to usb cable without battery, will ask for driver, show driver from C:\GSMULTI\UsbDrivers\INFINEON. 3. Open USBMap from C:\GSMULTI, select INFINEON and click MAPPING START, reconnect the phone to usb cable without battery. Some info will show on PORT/NAME, now SAVE & EXIT. 4. Open GSMulti main software, go to Setting(s) > Configuration, select DLL and firmware on S/W box, select USB as communiion then click OK. Now click START on main window, when the software says Wait Phone Connecting.. reconnect the cable. If flashing not start without battery just put the battery and slightly press power button.
Some new are from Infineon AGold plafrom, you need to install USB PortMapping Setup_1.7. Run USBMap_V07 from C:\GSMULTI, select INFINEON AGold Series and do mapping, rest of the procedure is same.
~Qualcomm~
based on Qualcomm platform are flashed with MDP, DP1, DP2 etc. Several updates came for these flashers.You need the USB cable, UART flashing not supported for this platform.
Flashing with MDP 1. Install United Modem Driver, connect the phone to PC through USB cable and let the drivers to be installed. 2. Opne MDP soft, click on the Select Port, new window will pop up.Your phone model and firmware version will be showed up there, if the phone is supported with that MDP version it will be automatically ticked on the checkbox. Now click Connect. 3. A new window will pop up for firmware selection. Browse and select your firmware folder in the Select box, all files will be automatically selected. You can change any certain file from the browse button. If you are using a DZ firmware click DZ button on the right lower corner of the window and and select that. 4. Select data handling option: NV Backup/Restore: NV Backup/Restore always have to be done, and it is default selected option. Backup the NV data and restore the backed up NV data automatically. Reset database & Contents: User related data including the setting data on the EFS is reset in the handset. The contents in the handset will be erased. Erase_EFS: The calibration data, user contents, media, and module will be erased. Only calibration data is kept when NV backup/restore is checked. Keep All Contents: No user data will be erased. 5. Now click Start and relax.
Emercy Download Mode: Qualcomm support a special mode named emercy download mode. In this mode, minimum units for downloading is occured so that users can download the s again in case of emercy situation. AMSS Modem, Media and Module s won't be flashed in this mode. You may need it when the not power on normally/incrorrectly flashed rlier etc.
Flashing with DP2 1. Downlaod DP2 V36 UMTS Setup and extract, go to DP2_31_INCLUDE_DP1_Setup folder and install the exe (use ). Now copy all the files from DOWNLOAD folder and paste on C:\DOWNLOAD (overwrite if needed). 2. Install United Modem Driver, connect the phone to PC through USB cable and let the drivers to be installed. 3. You'll need firmware in DZ format and the correct DLL for your model. 4. Open DP2_V36_UMTS (for example) from C:\DOWNLOAD, select UMTS in Division and click OK. 5. Select port (check Device Manager for USBModem Port ), you can set a range from sy select or select manually. Select DLL and select firmware in Downlaod Configuration. Click OK. 6. Click START in main window and connect the phone in Emercy download mode.
~ADI~
ADI are flashed with GSMulti. Can be flashed both in USB and UART mode, old phone only support UART.
ADI flashing on UART 1. Install and run GSMulti v30 2. Go to Setting(s) > Configuration, select DLL and firmware on S/W box, select UART as communiion, select correct port of Box/cable, then click OK. 3. Now click START on main window, when the software says Wait Phone Connecting... connect POWERED OFF phone with battery to cable and press POWER button.
ADI flashing on USB 1. Install GSMULti V30 2. Install MTK Download Setting. 3. Connect POWERED OFF phone to usb cable, will ask for driver, show driver from C:\GSMULTI\UsbDrivers\MTK. 4. Open USBMap from C:\GSMULTI, select MTK(ADI) and click MAPPING START, reconnect the phone to USB cable (re-insert battery also). Some info will show on PORT/NAME, now SAVE & EXIT. 5. Open GSMulti main software, go to Setting(s) > Configuration, select DLL and firmware on S/W box, select USB as communiion then click OK. Now click START on main window, when the software says Wait Phone Connecting.. reconnect the cable.Press POWER but if not start automatically.
~MTK~
MTK based are flashed with Leo Tool. You need COM box/cable to flash, USB not supported.
Flashing Procedure
1. Download and Install Leo Tool.
2. Open Leo Downlaod Tool, select correct COM port for your BOX/cable.
3. Click Setting and select firmware in pcs format, software will show waiting, connect phone to BOX/cable and press POWER button, keep pressed till the download at is finished.
4. Relse POWER button and let Leo Tool do the rest.
~TI~
TI are also flashed with GSMulti.
TI flashing on UART
1. Install and run GSMulti v30
2. Go to Setting(s) > Configuration, select DLL and firmware on S/W box, select UART as communiion, select correct port of Box/cable, then click OK.
3. Now click START on main window, when the software says Wait Phone Connecting... connect POWERED OFF phone with battery to cable and press POWER button.
TI flashing on USB
1. Install GSMULti V30
2. Install E_GSM_Device_Driver_OMAPV1030_1.0 from C:\GSMULTI\UsbDrivers\TI_NEPTUNE
2. Connect POWERED OFF phone to usb cable and install driver.
3. Open USBMap from C:\GSMULTI, select TI and click MAPPING START, reconnect the phone to USB cable (re-insert battery also). Some info will show on PORT/NAME, now SAVE & EXIT.
4. Open GSMulti main software, go to Setting(s) > Configuration, select DLL and firmware on S/W box, select USB as communiion then click OK. Now click START on main window, when the software says Wait Phone Connecting.. reconnect the cable.Press POWER but if not start automatically.
~SEMC (A2)~
Flashing Procedure
1. Downlaod DP2 V36 UMTS Setup and extract, go to DP2_31_INCLUDE_DP1_Setup folder and install the exe (use ). Now copy all the files from DOWNLOAD folder and paste on C:\DOWNLOAD (overwrite if needed). Copy meflash.dll from C:\DOWNLOAD\EMP_DL_USBDriver to C:\DOWNLOAD if not exist there.
2. Connect the phone in POWERED OFF/SPECIAL BOOT MODE (varies on different model) to usb cable and show driver from C:\DOWNLOAD\EMP_DL_USBDriver.
3. Open DP2_V34_UMTS_KF750 from C:\DOWNLOAD, select UMTS in Division and click OK.
5. Select DLL and click Run Download Configuration. Add .ssw files in E box and .map files in E GDFS box. Click OK.
6. Click START in main window and reconnect the phone in POWERED OFF/SPECIAL BOOT MODE.
No comments:
Post a Comment